Plastic painting tips

"Tarting up the interior."

Personalising the interior of the car is for many the first thing they do.

Although aftermarket interior modification parts look nice a custom look is within reach if you are prepared to put in a little effort and paint the interior yourself.

Preparation is the most important part in any paint work.

Whatever is between the part and the paint (i.e. chips, scratches, grease etc.) will show through the layers of paint.

That said, some colours are more forgiving than others.

Take your time. The final  job will last longer if you spend longer over it in the first place. Good preparation is VITAL!

Ok, first things first, you’ll need:

  1. Time. I can’t stress enough how important it is not to rush things.
  2. Paint, this will no doubt be in aerosol form. You will need some plastic primer (also known as adhesion promoter), base coat (you can use normal car paint) in whichever colour you wish to paint and some lacquer (gloss or Matt, it’s your decision.)
  3. Something to ‘key’ the part. In the trade we call it scotchbrite, it’s basically a rough pad used to remove the shine from a panel, and it leaves fine scratches for the paint to sit in/grip to. You could use something like 1500 grit wet and dry paper for this, but probably the best thing I can think of would be the rough part of a washing up sponge.
  4. Warm soapy water, or preferably a solvent based cleaner (something like white spirit – if you use this, wear gloves).
  5. Hot air gun or a hairdryer. This just makes life easier.
  6. If you can get one, a Tack cloth. This is used to pick up any little hairs/bits of dust both on the panel before painting and on the paint during painting. You can make do without a tack cloth, so don’t worry if you can’t get one.
  7. A Mask, preferably a vapour one.
  8. T-Cut or another finishing compound. And a soft cloth.

 Now you have the materials needed, let’s begin…

Stage 1 – Preparation

Remove whatever part you plan to paint. Be careful not to scratch or damage it, you’ll only be making yourself more work.

Once you have removed the part, start by washing it with the soapy water/solvent cleaner. This removes grease, dust or any other contaminates. If there is any damage to the part, now would be the time to sort it. Next start to ‘key’ the part, making sure there are no shiny areas left on it, the better you do this, the less likely the paint it to flake later. Once you have ‘keyed’ the part, wash it again. Make sure it is thoroughly dry before proceeding.

Stage 2 – Painting

The main bit of advice I have for painting with aerosols would be to warm the can(s). This enables the paint to be atomised finer as it passes through the nozzle, which results in a better finish. Bare in mind I said warm, DO NOT overheat, you are taking the chill off the can, not risking losing a hand due to an aerosol exploding while you hold it.

Make sure you give the can(s) a good shake before using them. The best technique for painting with an aerosol is to use light, overlapping strokes. You need to leave at least 5 minutes between coats to give the solvents in the paint time to evaporate.

This time can be cut by using a hairdryer. I would recommend either wearing a mask or going outside for this next bit, the vapours can be dangerous.

First apply the plastic primer, I would highly recommend you use this as it will give the paint something more to stick to than just the light ‘key’ scratches. You could skip the plastic primer stage, but if the part gets chipped the paint will start to flake off.

You may need to apply 3/4 coats of plastic primer, but you can use a hairdryer to speed the process of drying. Remember, a light coat often is better than a heavy coat less often. Plastic primer is generally quite thin, so be careful not to get any ‘runs’.

Once the plastic primer is dry it’s time to apply the base coat. Again, use light overlapping strokes. Depending on the colour, it may take anything from 3 to 8 coats to cover. Again, make sure you leave enough time between coats.

Once the colour has completely covered the part, you can start to apply the lacquer. This is not a necessity, but it helps to protect the base coat and adds a shine (if you chose gloss lacquer).

Apply this the same way as the base coat gradually building up the thickness of the lacquer. You’ll probably need about 4 or 5 coats of lacquer.

Leave the part for a good 3 or 4 hours before you try to polish and re-fit it. There is nothing worse than marking fresh paint work.

Good Luck

Notes:
I used normal car paint. Don't waste your money on so called 'plastic paints' when all you really need is a good key and some plastic primer. Also, people must remember that paint is not indestructible.
Good Key->Plastic Primer->Base coat->Lacquer
is all you should need.

(Article submitted by TheNamesJames - a forum contributor)

Please join us in our friendly forum where you can discuss your car styling project with our very friendly community of car enthusiasts. There are 1000's of tips and car specific questions in our forum and we have quite a few custom paint jobs/projects in progress in the gallery section.

Please Check out my YouTube channel, we're regularly adding new content...

PLEASE HELP: I NEED YOUR DONATIONS TO COVER THE COSTS OF RUNNING THIS SITE AND KEEP IT RUNNING. I do not charge you to access this website and it saves most TorqueCars readers $100's each year - but we are NON PROFIT and not even covering our costs. To keep us running PLEASE Donate here

If you liked this page please share it with your friends, drop a link to it in your favourite forum or use the bookmarking options to save it to your social media profile.

Feedback - What do You Think?

Please use our forums if you wish to ask a tuning question, and please note we do not sell parts or services, we are just an online magazine.

Help us improve, leave a suggestion or tip

Your Constructive comments on this article, I really want to improve this article with your help and suggestions.


Please watch this video and subscribe to my YouTube channel.



Member Benefits

Join our forum today and benefit from over 300,000 posts on tuning styling and friendly car banter.

You will also have full access to the modifed car gallery, project car updates and exclusive member only areas.

(All car owners of all ages and from all countries are welcome).