Torque Cars

Have you upgraded your brakes

Discussion in 'Brakes' started by obi_waynne, 12 April 2014.

  1. obi_waynne

    obi_waynne Administrator Staff Member Moderator

    Messages:
    41,343
    From:
    Deal, Kent UK
    Car:
    A3 1.4 TFSI 150 COD
    What upgrades have you made to your cars brakes?

    What are your plans for future upgrades to your cars braking system?
     
  2. old-git

    old-git Moderator

    Messages:
    9,182
    From:
    Essex
    Car:
    Elan & Robin Hood
    Yes, but for weight saving reasons only. The OEM calipers fitted to all four corners of the Elan gave more than enough braking performance.
     
  3. T9 man

    T9 man TC Pro Founder Moderator

    Messages:
    20,369
    From:
    London, UK
    Car:
    Saab 9-3SS T9
    I have gone from a single piston caliper (Factory OEM) setup to a 4 pot caliper and currently now running a 6 pot caliper system. The stopping power is very good as they have to stop a very heavy car, weight saving is not an option as I love my creature comforts.
     
  4. TCJBOLDIE

    TCJBOLDIE Torque King

    Messages:
    4,900
    From:
    Brisbane
    Car:
    JB Starion
    I have replaced the stock 250mm front discs with 296mm's and the sliding single piston calipers with 4 pots along with braided lines and RBF600 fluid fitted a Willwood bias adjuster installed SPEED BLEEDERS all round removed the front dust covers and installed cold air ducting to the centre of the front discs.

    The mods were engineered and a Blue mod plate fitted.

    I would have gone for larger discs IF I had the 17's that are on the car now

    I have tested them on the track @220k's and they didn't fade and had a firm pedal .
     
  5. Effect

    Effect Newbie

    Messages:
    3
    From:
    Brisbane, Qld, Australia
    Car:
    4WD
    Yes, I totally agreed with your post that car owner should be upgraded their's vehicle brake to extend the life of a vehicle.
     
  6. stamford

    stamford Pro Tuner

    Messages:
    3,800
    From:
    Hampshire
    Car:
    MG ZS200
    I have just reworked my braking system.

    x2 new handbrake cables.
    pair of new rear calipers and redstuff pads.
    MTEC dimpled and grooved rear discs.
    326mm vented front Brembo discs.
    Brembo GT2 4 pot calipers and DS2500 pads.
    HEL stainless lines all around.

    Will be flushing the 5.1 out and going with a better fluid.
     
  7. SLEEPER

    SLEEPER Pro Tuner

    Messages:
    2,783
    343mm ap racing discs and 6 pot calipers 34GTR vspec brakes on rear braided pipes (nismo) and ATE fluid

    Good brakes are worthwhile .These will stop 1700kgs of stagea from 170mph without any fuss or fade vvvvvery quickly

    Good tyres help as well (Toyo 888s)
     
  8. Guybo

    Guybo Torque Junkie

    Messages:
    162
    From:
    Tampa, FL, USA
    Car:
    13 GenCoupe 2.0T
    My stock brakes are fine. They work perfectly well and I won't be increasing engine output all that much (maybe 15%) and the stock brakes will handle that. Brakes are expensive!
     
  9. griffindai

    griffindai Torque Junkie

    Messages:
    204
    From:
    South Wales
    Car:
    Saab 9-3 v6 Aero
    Nothing major on mine, still the same 314mm Aero size but swapped to Mtec discs, yellow stuff R pads, HEL lines & RBF600 fluid.

    Stops fine, didn't break the bank and a massive improvement over standard! I cooked the brakes a day after the remap chasing down a M3 & stupidly quick CTR (CTR just slaughtered me!!!) Loadsa fun having no brakes for 3-400 meters!!! Brown trouser moment there!! Very very lucky!!!

    It's going back in Thursday for a full service and fluid change, new pads, yellows up front again but giving bluestuff NDX on the rear a try out.

    Once this JZW stage 5 tunes sorted (JZW stage 1 atm) I'll get saving for a 345mm set up off the vectra VXR or spend a bit more on the Maptun 4 pot kit. Can't see this current set up lasting long with the extra torque on tap, going from stg1 straight to 5 :)
     
  10. griffindai

    griffindai Torque Junkie

    Messages:
    204
    From:
    South Wales
    Car:
    Saab 9-3 v6 Aero
    How did you find the 4pots Os? I really should have gone for these from the off instead of buying all this audio gear!!
     
  11. claymore

    claymore The Torque Meister

    Messages:
    1,888
    From:
    Shrewsbury
    Car:
    T-10k,
    Gone from standard single pot with 280mm disks to 302mm disks then to 336mm disks with 4 pot Aston Martin calipers, and now on 380mm carbon ceramic brakes front and back. I don't think I'll need to upgrade the brakes again.
    pic of 336mm disk next to a Carbon one.

    [​IMG]

    [​IMG]
     
  12. RobBentley

    RobBentley The Torque Meister

    Messages:
    1,470
    From:
    Kent, UK
    Car:
    Audi RS6 C6 Saloon
    I've kept the factory 6-pot callipers, but upgraded the discs to an AP racing disc which has much larger cooling vanes, is a two piece disc and saves 6kg of rotational/unsprung weight per disc over the OEM disc. Discs are the same size as OEM obviously (390mm) but are far better. I've also added some better pads by way of Ferodo DS2500 as well.
     
  13. T9 man

    T9 man TC Pro Founder Moderator

    Messages:
    20,369
    From:
    London, UK
    Car:
    Saab 9-3SS T9
    The 4 pots were good Dave no complaints whatsoever, my problem was being at Neo's when the 6 pots arrived from MapTun for their track car - I'm so weak! :oops:
     
  14. HDi fun

    HDi fun TC ModFather

    Messages:
    15,384
    From:
    Buckinghamshire UK
    Car:
    Passat 2.0 TDi
    250mm is tiny. The stock rotors on my Passat are 345mm up front. But it does weigh as much as a small house.
     
  15. TCJBOLDIE

    TCJBOLDIE Torque King

    Messages:
    4,900
    From:
    Brisbane
    Car:
    JB Starion
    But you need to take into account that my car is an 85 model with 14 inch wheels and was considered quite advanced at the time with vented discs all round. 13 & 14 inch wheels were the norm at the time and the space available to fit brakes was governed by the X"factor.

    My car had the optional 15 in wheels at the time of the brake upgrade and the 294 mm discs and calipers have a few thou of clearance so that was the most brake that could possibly fit in the space available and work well at the track with repeated stops from 220kph:)

    today's cars have larger wheels that allow fitting of bigger brakes|B
     
    Last edited: 29 April 2015
  16. griffindai

    griffindai Torque Junkie

    Messages:
    204
    From:
    South Wales
    Car:
    Saab 9-3 v6 Aero
    your a sucka for shiny bits ;)

    Mines in now getting the brakes done, just had a call saying the rear calipers seized so I'll be gi ring Charlie a call tomorrow for a new one then get it sorted next time I'm home. Always something!!
     
  17. HDi fun

    HDi fun TC ModFather

    Messages:
    15,384
    From:
    Buckinghamshire UK
    Car:
    Passat 2.0 TDi
    Sorry - didn't know the age of car you were using. I'm old enough to remember 13" wheels. I had a 1985 Montego which had something like 256mm discs (solid) up front and the back was simple drum brakes. Again 14" rims.
     
  18. TCJBOLDIE

    TCJBOLDIE Torque King

    Messages:
    4,900
    From:
    Brisbane
    Car:
    JB Starion
    No Worries |B
    I always have a laugh when I see a car/SUV that has say 22 inch wheels and stock brakes as they look in proportion like the disc brakes on a pushbike :lol:
     
  19. tonytoni

    tonytoni Tuner

    Messages:
    61
    From:
    Las Vegas, Nevada
    Car:
    '04 Nissan Frontier
    I recently replaced my Honda Civic's brake pads with AEM High Performance Brake Pads. Got it from 4wheelonline. Haven't changed the brakes on my Nissan Frontier.
     
  20. TCJBOLDIE

    TCJBOLDIE Torque King

    Messages:
    4,900
    From:
    Brisbane
    Car:
    JB Starion
    I also have a Willwood bias adjuster that I have adjusted to allow more pressure to the front brakes
     
  21. HDi fun

    HDi fun TC ModFather

    Messages:
    15,384
    From:
    Buckinghamshire UK
    Car:
    Passat 2.0 TDi
    I see many small VWs with huge rims and tiny little rotors. Looks even sillier with drums at the back
     
  22. jdmeaux1952

    jdmeaux1952 Full member

    Messages:
    10
    From:
    Louisiana
    Car:
    Elantra GLD 05
    What I think looks stupid, and I repeat STUPID, are the guys who add caliper covers too large for their calibers, And YOU can notice it with the 22-inchers.

    I had upgraded the front calibers with EBC pads since they take about 80% of the braking force, With stock horsepower, thay are more than enough.
     
  23. HDi fun

    HDi fun TC ModFather

    Messages:
    15,384
    From:
    Buckinghamshire UK
    Car:
    Passat 2.0 TDi
    I'm not sure I'd consider EBC pads as an upgrade, my experience with them was dreadful. In fairness this was in 2004 so maybe things have improved since then.

    I had greenstuff in the front of my Nissan Primera and all they did was smoke under the slightest provocation.
     
  24. griffindai

    griffindai Torque Junkie

    Messages:
    204
    From:
    South Wales
    Car:
    Saab 9-3 v6 Aero
    Yellow stuff are good ;)

    The old yellow stuff pads were pretty dangerous though, they needed to be warmed right up to take any effect. The new (well few years old now) 'R' pads are miles better.....cheap too ;)
     
  25. George5

    George5 Newbie

    Messages:
    3
    From:
    Athens Greece
    Car:
    Renault5GTL1.1L1984
    I've done some changes to my braking system:
    -Rear drums from a renault clio 1 williams, new shoes from ate and regulated the springs
    -New ate typ200 racing brake fluids
    -Cleaned and regulated the drum brake distributor
    and I am going to regulate my brake calipers, fit some great pads(ebc or tarox) and new tarox super japan or g88 brake discs. But I have a question:
    The OE brake discs are 12mm thick and I plan to increase the thickness to 20mm(renault 5 gt turbo dimension). Will I need to change my brake calipers or the new discs will be able to fit under my OE ones? I will upgrade my calipers anyway but don't have the budget to buy them along with the discs and pads. So should I wait till I collect the money or I can do these 2 changes separately?
     
    obi_waynne likes this.
Loading...

Share This Page

Click Here
  1. This site, like pretty much every other site, uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are agreeing to our use of cookies, this may include third party cookies from our carefully selected advertising partners and for our analytics which allow us to see which pages are of interest and improve our site navigation and experience.
    You can disable cookies in your browser but this may affect your experience on this website.

    Dismiss Notice